1×6 @ 3 feet long 1 – 2×2 @ 8 feet long 1 – 1×4 @6 feet long 1 – 1×2 @ 8 feet long 1 – 2×4 @ stud or 8 feet length 1 – 1/2″ scrap plywood for seat top, 19″ x 19″ 1 yard of fabric 1 piece of foam, 19″ x 19″ 1″ thick 1 1/4″ pocket hole screws 2 – 2×4 @ 38 1/4″ (Chair back legs) 2 – 1×4 @ 17 1/2″ (Side Aprons) 2 – 2×2 @ 17 1/4″ (Front Legs) 2 – 1×4 @ 16″ (Front/Back Aprons) 4 – 2×2 @ 4″ (Supports – both ends cut at 45 degrees off square, NOT parallel to each other) 1 – 1×2 @ 16″ (Seat Back Top) 2 – 1×6 @ 16″ (Seat Back) 2 – 1×2 @ 19″ (Longest point, one end cut at 8 degrees off square) 1 – 1×2 @ 16 3/4″ (Center Support) 1/2″ plywood @ 19″ x 19″ (Seat top) If you follow these steps carefully, you can cut back legs that are straight and symmetrically to each other. Mark the legs as shown in the diagram. The front – where the chair leg connects to the side aprons – needs to be cut in 1/4″ to account for rounded edges on 2x4s.

The goal is to make as many cuts as possible with a circular saw, but you will need to finish inside cuts on the back with a jigsaw. Follow the diagram above carefully. I advise taking the scrap piece of 2×4 and cutting a leg first from it to get some practice. Once your legs are cut, lay them together, and check to make sure that the top, bottom and front sides all match. The other parts are not as significant. Sand your cuts smooth. Attach the side aprons to the back legs, flush to the bottom of the front cuts on your chair back legs. fabric club chair and ottomanMake sure the two leg pieces still match up – if not, your chair is going to be crooked!discount dining chairs brisbane Attach the front legs to the side aprons as shown above. wedding chair cover rentals wisconsin

The tops are flush, and your chair part should match up at this point. Attach the front and back aprons, carefully predrilling. I used pocket hole screws and glue. The cross supports will not only add strength to your chair, but it gives you something to screw your seat to. Attach the seat back top as shown above. I used pocket holes from the back but you can also use predrilled screws from the legs. Attach as shown above. The base supports will add considerable strength to your chairs. wicker chairs for sale ikea Attach the base center to the sides as shown in the diagram above.ski chair lift manufacturers Spray glue the seat cushion to the seat top plywood. where to buy cuddle chairLay fabric facedown on table with seat top on top of fabric, foam side down.

Staple fabric carefully to the underside of the chair, tucking corners neatly. Use 2″ screws to attach the seat to the cross supports or use pocket hole screws. This chair was painted with Valspar Antique White in Flat Enamel, three coats. A top coat (Valspar satin finish poly) was added. The fabric is from Joanns, and is part of the Home Decorator’s 45″ wide fabric, and was on sale for $5 a yard. For a foam pad, I used a discarded chair pad cut to size. Total cost of this chair was under $20. Chairs dining room Beginner Cottage Style Furniture Plans Wise Offshore Seating/Pedestal combinations let you create the ideal seating combination for your boat by matching the chair of your choice with the pedestal of your choice for a custom seat. The Deluxe Ladder Back Helm Chair with snap on/off cushions and padded aluminum armrests features a thick-wall, rotational-molded plastic construction frame. Thick foam padding is covered with 26 oz. UV- and mildew-treated marine-grade vinyl.

Manufacturer 6 year upholstery, 3 year frame, and 3 year hardware warranty. Dimensions: 19"H x 22"W x 22"D. Combine with the pedestal of your choice (sold separately) Thick-wall, rotational-molded plastic construction frame 26 oz. UV- and mildew-treated marine-grade vinyl Combine the Deluxe Ladder Back Helm Chair with the hardware combination (sold separately) of your choice: 15" fixed pedestal with fore and aft slide, adjustable pedestal with fore and aft slide, adjustable pedestal with seat mount spider, 15" fixed pedestal with seat mount spider, or aluminum fore and aft seat slide. Manufacturer model #: 8WD562-3-710. Mix-and-match Wise Offshore Boat Seat/Pedestal pieces sold separately can be found through keyword search by typing in the keywords "Wise Offshore Boat Seat/Pedestal Combinations"7 days a week: 7am to 10pm CT or call 1.800.227.7776 anytime Please enter a Zip Code to check availability of an item at a store near you.Disclosure: This painted ladder back chair post contains affiliate links for your convenience.

This curvy ladder back chair was dropped off by my customer. It has a woven rush seat and great curves. A little paint will bring this chair back to life. My customer has a gorgeous distressed black hutch and wanted her chair to compliment her favorite piece. Can you blame her?  That hutch is amazing! The first step was to tape off the woven seat area because we are leaving the rush in its original natural condition. The rush was pulled away from the legs of the chair as much as possible. The chair was then sanded, cleaned and prepped for paint. Next, the seat was flipped over to paint the underside first. We chose a pure black paint, using Kristi Kuehl Pure Home Paint Derby. I also covered the woven seat to protect it from any paint splatter, because I actually am quite messy when I work. The chair was painted and then lightly sanded, using flexible sandpaper to achieve a smooth finish all around.  The flexible sandpaper works especially well with all the curves of the chair.