Installing chair rail molding on an angled cut so it will fit in a corner sounds like a complicated task, but it really isn’t. Chair rail molding is place on a wall about the height of a chair back and was originally designed to protect the wall from that chair back. Today, installation of chair rail molding is basically decorative. Follow these instructions to complete a successful project. •Railing (molding of your choice) •Chalk or pencil marker •Hammer with finishing nails •Paint or stain with brushes •Wood putty with knife Step 1 – Measure the Walls Take careful measurements to determine the amount of railing to purchase, especially if you want to cover more than two walls. Step 2 – Paint or Stain Once you’ve selected your style of railing to install, paint or stain it first. Step 3 – Draw an Installation Line Measure the height to the spot on the wall where you will install the chair molding. Draw a straight line according to a level along the wall from corner to corner.

Step 3 – Start with Complete Wall Measure a complete wall without any doorways or windows first. Cut the rail at the end on its side producing a 45-degree angle. You will cut a connecting piece of rail likewise. Step 4 – Corner Cuts Make a 45-degree angle cut for each end that meets in a corner. Make sure the railing is on its side when cutting. However, if using a style of wood that is beveled, you will need to cut one piece in the opposite direction of the other. If the wood is uniformly thick with no decorative beveling, make two identical 45-degree angled cuts with the rails on their sides. Check to see that the corner pieces of rail connect properly before proceeding. You may need to adjust the cuts Step 5 – Nail Railing Using the assistance of a helper who holds the railing wood in place along the designated line, nail the corner wood section in place first every two feet as close to the edge without splitting the wood. Join the connecting corner wood piece next making sure the two fit perfectly.

They should if you tested the connection after the initial cuts. Using a nail gun would make the job easier and help prevent any wood splitting from occurring. salon chair on ebayUse a level to make sure the installation is straight. baby rocking chair plansYou should arrive at four corners covered extending out to the middle of each wall using eight pieces of railing. red leather chair ikeaInstall carefully measured middle pieces to connect to the corner rail pieces already installed.table and chair rentals austin tx Step 6 – Apply Wood Puttyantique chairs for sale melbourne

Finish off the project by applying wood putty with a putty knife to any nail head holes and any gaps found between connecting pieces of railing. folding wooden chair step stoolSand the wood putty smoothly once dried and touch-up with the same paint or stain you originally used on the wood before installation.rocking chairs for outdoor use •Make any corner outer cuts so the chair rail with an angle goes past the corner.cheap comfy outdoor chairs •Make an inside cut so the chair rail angle goes into the other corner cut.desk chair for dorm •Always use protective eyewear and gloves when operating a power saw or other tool. Jump to: navigation, search

A dado rail, also known as a chair rail, is a type of moulding fixed horizontally to the wall around the perimeter of a room. Diagram of a wall illustrating the crown molding (top), dado rail (middle) and the skirting board (lower). The dado rail is traditionally part of the dado or wainscot and, although the purpose of the dado is mainly aesthetic, the dado rail may provide the wall with protection from furniture and other contact. Traditionally, the height of the dado rail is derived from the height of the pedestal of a column of classical order, [1] typically 24 inches from the floor or about one-fifth the height of the room. Modern trends have been towards 36 inches or 900 mm, [2] based on the assumption that its purpose is to protect the wall from chair backs. The term 'chair rail' is also used for this reason. Dado rails are also sometimes applied to a wall without the full dado treatment. The purpose of the rail in these cases may be protective, and it is common in environments where walls are subject to a lot of wear and tear, such as shopping centres and hospitals.

In such cases the height of the rail is often 1200 mm or even 1500 mm from the floor and serves a functional rather than aesthetic role. ^ Trim Carpentry Techniques: Installing Doors, Windows, Base and Crown, Craig Savage, Taunton Press, 2002, ISBN 1-56158-321-9, p.140Chair Rail Molding and Two Tone Paint One of the easiest and cheapest ways to give your house a new look is to grab a paint brush and begin painting. A new coat of paint can do wonders for a drab room that needs a boost. Another great idea is to add chair rail molding. Both of these techniques use inexpensive materials to makeover a room, and don’t require an excess of effort. Using two colors of paint to decorate a room is a great idea to give it more pop, pizazz, and just makes it stand out more overall. Neutrals are an excellent choice of paints because they make the room look more spacious and open. Additionally, they allow for other decorating ideas that might be more bold or bright than the paint, or to simply add accessories and decorations.

But not to worry, neutral color paints allow you to do this without making the room look flashy or gaudy. In most cases, it is best to paint the top part of the area the lighter of the two colors. This will make the room appear more open, spacious, and larger. This is not always the case, though. Definitely buy different color swatches to compare and contrast ahead of time. Another tip to make a room seem more open and brighter is to use two similar colors. Choose colors that are within the same color scheme or family. For example, pair a dark brown with a lighter brown or tan color to give the room an inviting feel. Chair rail moldings are a must in any household, especially in areas with many chairs, end tables, or other furniture that might be moved frequently. Chair rail moldings keep the walls from being scuffed by chairs or other furniture. Additionally, chair rail molding has an aesthetic appeal to it. Believe it or not, there is a science to placing chair rail molding.

Many people place the moldings at the wrong height. Doing so can make a room feel wrong or off balance. It is suggested that chair rails be placed at a third of the ceiling height. Most ceilings are 8 feet high, so the chair rails should be installed about 32 inches from the floor. And if you are ever unsure, it is better to err on the lower side. Lower chair rails are definitely better than high chair rails. As in using paint to accentuate rooms, it is advisable to use two different colors on the chair rail moldings and the walls to create a visually appealing room. Doing so will create dimension, depth, and energy to the room. There are many different techniques to changing the look of a room using paint in different-but-complimenting colors, and by using chair rail moldings. Both ways of decorating add depth, dimension, and life to an otherwise dull and lifeless room. Try using one or both of these options to create a whole new room without much effort or expense. Your senses and your wallet will thank you.